dc.contributor.advisor | Sierra del Río, Jorge Andrés | |
dc.contributor.author | Graciano Uribe, Jonathan Andrés | |
dc.date.accessioned | 2019-11-12T16:35:18Z | |
dc.date.available | 2019-11-12T16:35:18Z | |
dc.date.issued | 2019 | |
dc.identifier.uri | http://hdl.handle.net/20.500.12622/1451 | |
dc.description.abstract | La energía hidroeléctrica es la principal fuente de energía renovable en el mundo, por lo que su interés en el campo científico ha sido permanente. Una tecnología de generación hidráulica son bombas operando como turbina (PAT). Sin embargo, en comparación con otras tecnologías de energía limpia, la tecnología PAT no ha encontrado mucha literatura en la investigación académica publicada, lo que contribuye a su limitada comprensión de la comunidad académica. Este trabajo propone el estudio del parámetro geométrico de mayor incidencia (redondeo en la entrada del álabe) en el punto de máxima eficiencia (BEP) de una bomba centrífuga comercial. Utilizando ingeniería inversa, se crearon modelos geométricos del impulsor y de la voluta. Su comportamiento dinámico del fluido fue evaluado en modo bomba, basado en estudios numérico-experimentales. Validando el método numérico, se determinó el comportamiento de la PAT con la misma metodología de simulación, obteniendo así la curva característica del PAT. Posteriormente se editó la geometría del impulsor con el objetivo de implementar el redondeo en la entrada del álabe en el impulsor encontrando un incremento de la potencia generada en un 3,142% | spa |
dc.format.medium | Recurso electrónico | spa |
dc.format.mimetype | application/pdf | |
dc.language.iso | spa | |
dc.publisher | Instituto Tecnológico Metropolitano | spa |
dc.rights.uri | http://creativecommons.org/licenses/by-nc-nd/4.0/ | * |
dc.subject | Bombas centrífugas | spa |
dc.subject | Turbomaquinaria | spa |
dc.subject | Simulación númerica | spa |
dc.subject | Control programable | spa |
dc.subject | Sistemas hidráulicos | spa |
dc.subject | Energía hidroeléctrica | spa |
dc.title | Caracterización de una bomba centrífuga operando como turbina, utilizando técnicas de simulación computacional de fluidos | spa |
dc.publisher.faculty | Facultad de ingenierías | spa |
dc.publisher.program | Maestría en Gestión Energética Industrial | spa |
dc.subject.keywords | Pumping machinery | eng |
dc.subject.keywords | Pumping machinery | eng |
dc.subject.keywords | Water power | eng |
dc.subject.keywords | Piezoelectric transducers | eng |
dc.subject.keywords | Turbines | eng |
dc.subject.lemb | BOMBAS (MÁQUINAS) | spa |
dc.subject.lemb | ENERGÍA HIDRÁULICA | spa |
dc.subject.lemb | ENERGÍA MECÁNICA | spa |
dc.subject.lemb | TRANSDUCTORES PIEZOELÉCTRICOS | spa |
dc.subject.lemb | TURBINAS | spa |
dc.description.abstractenglish | Hydroelectric energy is the main source of renewable energy in the world, because of this, the interest in the scientific field has been permanent. A hydraulic generation technology are pumps working as turbine (PAT). However, compared to other clean energy technologies, PAT technology has not found much literature in published academic research, contributing to its limited understanding of the academic community. This paper proposes the study of the highest incidence geometric parameter (inlet blade rounding) at the maximum efficiency point (BEP) of a commercial centrifugal pump. Using reverse engineering, geometric models of the impeller and volute were created. Its dynamic fluid behavior was then evaluated in pump mode, based on numerical-experimental studies. Validating the numerical method, the PAT behavior was determined with the same simulation methodology, thus obtaining the characteristic curve of the PAT. Later the impeller geometry was edited with the objective of implementing the blade rounding at the impeller inlet finding an increase of the power generated by the PAT in 3.142 | eng |
dc.description.degreename | Magíster en Gestión Energética Industrial | spa |
dc.identifier.instname | instname:Instituto Tecnológico Metropolitano | spa |
dc.identifier.reponame | reponame:Repositorio Institucional Instituto Tecnológico Metropolitano | spa |
dc.identifier.repourl | repourl:https://repositorio.itm.edu.co/ | |
dc.rights.local | Acceso abierto | spa |
dc.rights.accessrights | info:eu-repo/semantics/openAccess | |
dc.rights.creativecommons | Attribution-NonCommercial-NoDerivatives 4.0 International | * |
dc.type.local | Tesis de maestría | spa |
dc.type.coar | http://purl.org/coar/resource_type/c_bdcc | spa |
dc.type.driver | info:eu-repo/semantics/masterThesis | spa |
dc.publisher.grantor | Instituto Tecnológico Metropolitano | spa |
dc.relation.cites | Revista CEA | spa |